How To Set A Grandfather Clock Moon Dial
INSTRUCTIONS FOR KIENINGER (KSU) GRANDFATHER CLOCKS
WHEN HANDLING EXPOSED Brass PARTS, USE SOFT Cotton wool GLOVES TO PREVENT TARNISHING.
1. SETTING UP The GRANDFATHER CLOCK
Set clock upright on solid surface. Remove all packing material from within of Granddad Clock. Set clock where you desire it and level on side and front of waist.
(In that location ARE LEVELING FEET IN EACH CORNER ON BOTTOM OF CLOCK.) MAKE
SURE CLOCK IS LEVEL.
ii. ATTACHING PENDULUM
Attach the pendulum on the leader.
3. ATTACHING WEIGHTS
Attach the weights on the pulleys, making sure the cablevision is in the groove effectually the pulley. When facing the clock (On Grandpa Clocks, the weight on the left weighs approximately vii lb., the centre and the one on the right approximately 9 lb.,
On Grandmother Clocks, the weight on the left and center weighs approximately 7 lb., the i on the correct approximately ix lb.)
The pulleys are packed separately. The cease of the cable goes through the pulley and up to the lesser of the clock movement. Look at the bottom of the weights to see if they may be marked: L or C or R for Left, Center and Right facing the clock.
4. STARTING CLOCK
Hold pendulum on bottom and push button all the way to the left or right, concord steady and release. (YOUR CLOCK IS EQUIPPED WITH AN Automated Beat out Aligning AND Every bit THE PENDULUM SWING SLOWS, THE VERGE Volition Set ITS OWN Trounce)
v. WINDING THE CLOCK
Insert the crank into each keyhole in the dial and turn the crank counterclockwise to the left. A clicking noise while
winding is normal. Crank up the weights until against.
- The left weight is for the strike.
- The center weight for the time.
- The right weight is for the quarter hour chime and chinkle tune.
Letting the weights go all the manner to the bottom volition non damage the clock if you lot forget to pull upward the weights.
vi. SETTING THE TIME
To set the Kieninger grandfather clock to the correct time, move the minute hand clockwise or counterclockwise. There is no need to stop every quarter hour to let information technology chime. If the chiming cycle does not correspond to the time shown past the hands, it will self-correct within
two hours. When moving the minute manus past the 12:00 o'clock position, (stop at 12:00) wait until it is finished chiming and striking so advance to the right fourth dimension.
seven. SELECTING THE CHIMES
To select either the Westminster, St. Michael or Whittington chimes, shift the chime selector lever on the right-manus side of the dial, (beside the 3). The chimes tin can besides exist silenced. To silence the hour strike, shift the lever on the left-hand side of the dial,
(beside the nine). (IF YOUR CLOCK IS EQUIPPED WITH THE AUTOMATIC NIGHT Shut-OFF Characteristic, MOVE THE
LEVER ON THE LEFT TO THE CENTER POSITION AND THE CLOCK WILL Not Chime OR STRIKE FROM 10:15 PM TO 7:00 AM) If clock strikes at 10:15 PM to 7:00 AM with auto close-off engaged, advance hands 12 hours. (See No 6, setting the time)
DO Not Motion THE Chime OR STRIKE SELECTING LEVERS WHILE THE CLOCK IS CHIMING OR Hit
8. TIMING THE CLOCK
To regulate clock if it gains, turn the rating nut on the bottom of the pendulum bob to the left to lower the bob. If information technology loses, turn the rating nut to the right to raise the bob.
nine. SETTING THE MOON Dial
The arch of the moon dial is calibrated into 29-ane/ii days, respective to the lunar month. There are 59 teeth cutting effectually the border of the moon disc. A small gear is mounted on the paw shaft to mesh with the larger wheel about the mitt shaft. This
train of wheels moves the disc forrard at a speed of 1/2 a revolution in 29-1/ii days, completing the lunar month.
The moon punch is every bit authentic as it is applied to make information technology. Really, information technology is a trifle off, and if you lookout man the moon stage, you will have to adjust it every few months. The moon actually circles the earth in an average of 27 days, 7 hours, 43.2 minutes, and the period of time from the new moon is 29 days, 12 hours, and 44.05 minutes, non the verbal 29-i/2 days measured by your clock.
The moon disk tin can exist moved past hand in the back of the dial. Identify the moon exactly beneath No. xv on the moon dial.
Using a calendar, make up one's mind the number of days since the last total moon. Move the moon disk, one click in a clockwise direction for every day since full moon, .e.thousand., the moon is five days after total moon, move the moon disk five clicks. Should the moon gears be agile, the disk cannot be turned. Move the minute hand clockwise (as many hours as needed) to take the gears out of action, then fix the moon disk and readjust the fourth dimension.
10. SERVICING YOUR CLOCK
Nosotros recommend having your clock oiled every iii years past a professional clockmaker.
Your clock is a precision instrument, only it volition remain and then simply with regular upkeep.
Never use sewing machine oil or spray lubricants.
TO Adjust CHIME HAMMERS
During handling, the chime hammers may get aptitude out of adjustment causing improper tone in chiming. The chime
hammers are attached to thin brass wires, which may be bent to bring the hammers into proper alignment. From the sides of the grandfather clock, check the position of the hammers. The hammers should rest virtually 1/eight inch abroad from the chime rods. They should be aligned to strike the middle of the rods. The hammers should non impact or rub against each other.
ane Chimes volition sound dull or muted if hammers balance on the rod. To right, bend the hammer abroad from the rod.
2 Chimes are non clear. One or more than notes may not be heard. Hammers are to far from the rod. To correct, bend the
hammer toward the rod.
3 The Westminster chimes will operate in the following sequence:
· Quarter hr — 4 notes
· Half hour— viii notes
· Iii-quarter hour— 12 notes
· Hour chime— xvi notes
4 The Whittington and the ST. Michael chimes will operate in the following sequence:
· Quarter hour — eight notes
· Half hr— 16 notes
· Three-quarter 60 minutes— 24 notes
· 60 minutes chinkle— 32 notes
v Immediately following the hour chime the correct hour will be struck.
TROUBLE SHOOTING CHECKLIST
If your clock is not operating properly, the following adjustments can be made quite easily:
one. CLOCK DOES NOT RUN
a. Check that all three weights are fully wound.
b. Cheque to see that all packing cloth is out of the clock.
c. Check the clock easily. If the hands are catching on each other, bend the minute hand abroad from the hour hand.
2. CLOCK IS NOT CHIMING PROPERLY
a. It is normal if the chime sequence is disturbed after setting the clock to the correct time. Inside two hours, the chinkle
sequence will correct itself.
b. If the clock continues to chinkle out of sequence, perform the following adjustment:
i. Manually turn the clock through two hours, stopping at each quarter hr to allow it to chinkle. If, when the full
hour chime sequence (xvi notes) is sounded, the infinitesimal hand is not at the 12:00 position, remove the paw nut,
pull off the minute paw and position it to point at 12:00. Replace the manus nut.
c. If the chiming bike starts a few minutes before or afterwards the quarter hour position, perform the following aligning:
i. Move the minute hand to the adjacent quarter hour SLOWLY and note the position of the manus when chiming
started. Remove the hand nut and the minute hand. Grasp the small bushing under the minute mitt deeply with pliers and move the manus in the management to get in coincide with the correct quarter-hour marking.
iii. CLOCK IS Not COUNTING THE Correct 60 minutes
a. If the hour manus and the hr struck do not friction match, perform the post-obit aligning:
i. Manually chime the clock until the full hour is sounded and the hour is struck. Button the hour hand firmly until it is pointing at the hour but struck. The hour hand is on the shaft friction tight. If information technology is too loose, remove the hr and slightly clasp together the projecting role on the dorsum of the hand. Replace the hour hand by pointing it to the
correct 60 minutes.
New Grandfather Clocks can exist seen hither.
How To Set A Grandfather Clock Moon Dial,
Source: https://www.grandfatherclocks123.com/clock-news/instructions-for-kieninger-grandfather-clocks
Posted by: jaegerhistalt.blogspot.com
0 Response to "How To Set A Grandfather Clock Moon Dial"
Post a Comment